Chain ID and RPC URL: What Each Berachain Field Does
What is a chain ID and RPC URL? The chain ID identifies Berachain; the RPC URL connects your wallet to a node that reads network data and sends transactions.
By The Coin Wire Editorial4 min read

Correctly setting Berachain’s chain ID and RPC URL lets your wallet identify the network and communicate with it before you bridge assets. The chain ID is the network’s fixed identifier; the RPC URL is the endpoint MetaMask uses to ask a node for data and submit transactions.
What does Berachain’s chain ID identify?
Berachain’s mainnet chain ID is 80094, a fixed number that distinguishes it from Ethereum and other networks. Ethereum mainnet uses chain ID 1. The number identifies the chain for wallet and transaction purposes; it is not a wallet address, token, or server location.
A useful comparison is a country code and a phone line. The chain ID tells MetaMask which network a transaction belongs to, while the RPC URL is like the line the wallet uses to reach a service on that network. Both fields matter, but they answer different questions.
The chain ID also has a role when you sign. EIP-155 incorporates the chain ID into transaction signing so that a transaction intended for one chain cannot simply be replayed on another chain using a different ID. The wallet therefore needs the right network identity before it asks you to approve a transaction. EIP-155 describes this replay protection.
For someone adding Berachain in MetaMask, the practical check is that the network’s configured ID matches the ID reported by the RPC endpoint. If you enter a different chain ID, MetaMask can reject the network because the endpoint and the setting disagree. A familiar network name or logo does not resolve that mismatch; the number is the identifying value.
What does the RPC URL do?
The RPC URL connects MetaMask to a node that can answer requests about the chain and receive signed transactions for broadcast. RPC means remote procedure call: the wallet sends a structured request to the endpoint and gets a response, such as current network information or transaction status.
In practice, the wallet uses the endpoint while you view balances, prepare a transaction, or submit one after signing. The endpoint is a route to network services; it is not Berachain itself, and changing it does not change the chain ID. A slow or unavailable endpoint can make the wallet appear stuck even when the chain ID is correct.
That distinction matters before a bridge transfer. The Berachain bridge is used to transfer assets across chains so they can be used in Berachain’s DeFi ecosystem. The bridge adds the cross-chain asset transfer to the picture; the chain ID and RPC URL in your wallet still determine how MetaMask identifies and reaches Berachain when you interact with it.
Can you replace the RPC URL without changing the chain?
Yes. You can switch to another RPC provider serving the same Berachain mainnet and keep the chain ID at 80094. This is useful when the configured provider is slow or down. The alternative is to wait for that provider to recover; changing the endpoint can restore wallet access sooner, but it does not change the underlying network or make a transaction faster once it is on-chain.
Say you replace one Berachain endpoint with another. If both report chain ID 80094 and serve Berachain mainnet, MetaMask can use the replacement while retaining the same network identity. A provider for Ethereum, by contrast, reports a different chain ID. Substituting its URL while leaving Berachain’s ID in place creates a mismatch rather than an equivalent route.
The endpoint is therefore replaceable, but the number is not a preference to tune. The chain ID must identify the chain you intend to use. When MetaMask reports a mismatch, treat that as a signal to recheck the URL and ID against an authoritative source rather than trying nearby values.
How should you verify the settings before bridging?
Verify Berachain’s network details against Berachain’s official information or Chainlist, then compare the configured chain ID and RPC URL with those details. Avoid copying settings from an unfamiliar page: an RPC provider can return misleading data, even if the network name displayed in MetaMask looks right.
Check the chain ID first: Berachain mainnet should be 80094. Then confirm that the RPC URL is a provider intended for Berachain mainnet and that MetaMask accepts it as reporting the matching ID. If the endpoint is unavailable, use another listed provider for the same chain, preserving 80094.
Berascan is a block explorer, which is useful for looking up network activity; it is not the RPC URL field in MetaMask. The wallet setting needs a node endpoint. Keeping those roles separate makes the final check straightforward: the chain ID says which network you mean, and the RPC URL says which node MetaMask will contact.